Toyota 4d smart key programmer red OBD Matching instrument

Description

Toyota Smart Key maker 4D chip Toyota Smart Keymaker OBD2
Toyota Smart Key Matching
(Supporting Toyota Lexus smart keys) 4D chips before 2008
Safe and efficient: Adding a key only takes about 20 seconds; Using security will not compromise the anti-theft system
Supports all intelligent key anti-theft systems of Toyota Lexus, supports K-line and CANBUS protocols, is
At present, it is the fastest and safest instrument to lose all keys in the Toyota and Lexus series
The specific operation steps are as follows: (Please carefully read the usage steps and important prompts below)
@Using the smart key:
(1) Adding other keys to the main key:
1. Insert the m
atching instrument into the car diagnostic interface OBD, and when the matching instrument is powered on, it will emit a short sound
With a beep, the instrument enters automatic vehicle search mode.
2. Press and hold the start button twice to wake up the anti-theft computer. After 7 seconds, the device successfully connected to the car,
The de
vice will beep 4-5 times, indicating that the system is a 4th generation K system, called a 5-tone meter
The display system is a 5th generation CANBUS system; After waiting for 30 seconds, the instrument will "drip"
Changming indicates that the car has entered the "increased key state"
3. Add smart key: Place the original smart key (marked side) close to the start button
You will hear two beeps, and the SEC light will flash twice; Within 5 seconds, get your horse
The equipped smart key is close to the "start button", and you will hear two beeps, "SEC"
The light will flash twice; After learning all the smart keys, wait for 30 seconds until the SEC light flashes,
The system will automatically shut down the learning mode.
(2) When all keys are lost or only a secondary key is available, initialization is required:
1. Press and hold the LED button on the device, insert it into the OBD, and wait for the device to beep twice
Release the button, and the device will enter the search vehicle state.
2. Press and hold the start button twice to wake up the anti-theft computer. In 7 seconds? Zha Ming Fen Lou Yue Jie Ying Sun σ Look?  Will beep 4-5 times, (4 times indicates that the system is a 4th generation K system, and 5 times indicates that the system is5th generation CANBUS system); After 5 seconds, the "SEC" light will turn off; Waiting for 10-16 minutes
The device behind the clock will beep for a long time, and the SEC light will flash, indicating that the car has entered the "learning key" mode Status
3. Key all lost matching mode: Put each smart key that needs to be learned (with a marked side)
Approaching the start button, you will hear two beeps and SEC will flash twice; When you finish learning
After all the smart keys, wait for 30 seconds until the "SEC" light flashes, and the system will automatically shut down
Learning mode.
Important reminder:
1. It is necessary to use the correct brand new smart key and follow the correct operating steps, otherwise the consequences will be
Arrogance
2. If it is found that the key cannot be matched and the "SEC" light keeps flashing, T300 or other instruments can be used
Enter the anti-theft system to clear the fault code.
2. If after learning the key, the key can start but the SEC does not turn off, it may be that you are using the key
The key is a secondary key, and the learning mode can only be manually turned off using the main key.
3. Do not attempt to open the instrument casing and circuit board, otherwise you will bear the consequences.
4. This instrument is only for legitimate automotive maintenance purposes and cannot be used for other purposes; And it is necessary to abide by when
Local laws and regulations, otherwise the consequences shall be borne by oneself.
Toyota regular 4D key matching
Safe and efficient: Matching a key only takes about 20 seconds; Using security will not cause the anti-theft system to fail. Supports
The 2nd and 3rd generation anti-theft systems of the TOYOTA series are currently the fastest and safest to match Toyota keys
Instruments
The specific operation steps are as follows: (Please carefully read the usage steps and important prompts below)
1. Use a key with the correct 4D chip to turn on the ignition switch to "ON"
2. Insert the matching instrument into the car diagnostic interface OBD, and when the matching instrument is powered on, it will emit a short sound
The "Di" instrument enters the automatic vehicle search state, and after 5 seconds, it successfully connects to the car computer
The device will make three beeps, indicating that the vehicle has entered an initialization state. After a few seconds
The instrument will make a long beep, indicating that the car has entered the "matching key state".
3. Pull out the OBD matching device.
4. One, match 2 main keys and 1 secondary key to the IMMO computer (note: mandatory)
Two new master keys and one secondary key are required to close the matching program
a) Close all car doors
b) Insert the first new key into the ignition lock for 5 seconds (only the key cannot be inserted to turn on the ignition!)
c) Insert another master key into the ignition lock for 5 seconds (only the key cannot be inserted to turn on the ignition!)
d) Insert the secondary key into the ignition lock for 5 seconds (Just inserting the key cannot turn on the ignition!!!)
e) The new ignition key will be confirmed by the new IMMO
2、 Only match 1 or 2 master keys to the IMMO computer (must be manually matched after completion)
Turn off matching mode)
a) Close all car doors
b) Insert the new master key and wait for 5 seconds (it just won't turn on the ignition!!!)
c) Insert another new key and wait for 5 seconds (it just won't turn on the ignition!!!)
d) Remove the key from the ignition lock
e) Insert the first matching master key, quickly turn on and off the ignition switch 5 times, and then remove it
f) The new ignition key will be confirmed by IMMO
Important reminder:
1. It is necessary to use the correct Toyota 4D chips and follow the correct operating procedures, otherwise the consequences will be borne by oneself
2. If it is found that the key cannot be matched and the "SEC" light keeps flashing, T300 or other instruments can be used
The anti-theft system will clear the fault code. If the problem still cannot be solved, the anti-theft system must be replaced
The box was disassembled and the data was modified.